Properties of the bond. •. KLEIBERIT , as a one component glue, meets the requirements of stress group D3 according to DIN/EN (See test certificate. Kleiberit PVA/MDF Glue. (KL) Safety Data Sheet. Safety data sheet according to EU / Printing date Revision: Version-No. D3 Adhesive KLEIBERIT D3 Adhesive , proven a millionfold, is a water re- sistant white glue for D3 bonding according to DIN/EN and also. D4 with.

Author: Zulkirr Dutaxe
Country: Monaco
Language: English (Spanish)
Genre: Business
Published (Last): 17 December 2014
Pages: 324
PDF File Size: 7.2 Mb
ePub File Size: 15.94 Mb
ISBN: 906-6-31261-564-7
Downloads: 30421
Price: Free* [*Free Regsitration Required]
Uploader: Shaktishicage

After kkleiberit of pressing time, its strength decreased and fell below the values of Kleiberit The aim of this study is to determine the values of strength of bonded joint with use of PVAc adhesives within certain time periods, and further to compare PVAc adhesives from various manufacturers and find out differences among them.

Learn something new everyday. Strength increase in bonded joints over time, 5 min to 8 h Fig. It is recommended that the bonded parts of these test objects are not attached to one another with the same direction of annual rings. To activate, use the link in the E-mail that kleibreit have sent to you.

Index of /uploads/uhsoman/Kleiberit

Different adhesives are used depending on the requirements. A warm heated environment would be beneficial. Adhesive selection focuses on the materials being used, the environment where the furniture will be used in the future, and the technical parameters in production.

They do have a “Titebond Regular” kkeiberit can be used down to 2 Degrees C, but I haven’t seen it in retail sized packs in Australia – only in 20 litre and bigger industrial size containers, and then only at specialist industrial adhesives suppliers. Production of ladders, doors, furniture board, shponirovaniye.

The test objects were evaluated in a device such that both ends of the keliberit were clamped in the machine jaws along a length of 40 to 50 mm.

The hardening of PVAc dispersions involves no chemical reaction or structural change. According to the manufacturer, those glues have “minimum use temperatures” of 10 Degrees C, 13 Decrees C and 8 Degrees C respectively.


Click here if you notice an image that violates copyright or privacy rights.

This statement is confirmed by the results of our measurements summarized in Tables 2, kleiberir, and 4. Not only is the appearance a decisive factor, the properties during subsequent processing and use are also important.

The ultimate strength of the adhesives tested stabilised at values from There ya go eh?

Another objective is to compare results with other authors. We created a Personal Account for you to make the process of buying faster and easier in the future. The times shown are times after the start of pressing following the start of the test in the tensile testing machine. Decades of experience and close cooperation with machine and material manufacturers ensure consistent quality and reliability. In some instances the glue can become unusable once it has frozen and is a bin job after that.

Tensile shear test The test objects were evaluated in a device such that both ends of the object were clamped in the machine jaws along a length of 40 keliberit 50 mm. This means that PVAc adhesives kleibedit evolved sincebut the evolution has not affected the speed of the strength increase in the bonded joint.

September 3, ; Peer review completed: For Kleiberit and Provotil, the average strengths of the bonded joints after 1 h of curing were 6.

Delivery by haulers across all Ukraine.

Glue for a tree of KLEIBERIT D3, D4 buy in Chernovtsy

When clamping the objects in the test machine, the tensile force must act centrally and at the plane of the adhesive layer. Propellerleim 3W, 4B Plus showed a statistically significant difference between 7 and min of pressing time, over which range it showed the highest strengths.

Widths of to are in use. To Compare the Products. Invalid results are those where the failure occurs in the wood rather than in the adhesive layer, or where it is visually evident that the adhesive was not applied properly.

Info Sheets and Brochures

The test objects were made by simple lapping method Fig. Primary Processing Woodworking Machines: The process is slower in colder temperatures and if the temperature is too low then the process halts altogether. Your message must contain at least 20 symbols.


This research project deals with PVAc adhesives, 3003 properties, and conditions of use. Wonder what glue the chippies down in Antarctica use? Pasting of strong and tropical breeds of wood. Arrangements were made so that the force would act centrally and along the bonding plane. Ok, I kleigerit have got that one wrong. The invisible glue line is the benchmark.

Test device The test device was a testing machine with a constant speed of thrust as described in ISO Here’s a link to the Titebond Glue Specifications: In comparison to conventionally lacquered panels, the processing properties during drilling, milling and kleibeerit are especially impressive. Hi, PVA dries in the cold but does not set, it becomes powdery and does not hold any more than two bits of dry timber. Number of test objects The test was performed with enough test objects so that each test would produce at least 10 valid results.

Interestingly Sellys perfectly good glue – unless kleibsrit are a Titebond snob Aquadhere regular kleiiberit exterior only say that the glue will set more slowly in cold conditions. Below 8 degrees most PVA style glue start congeal, making them unusable.

I checked the Selley’s web site for the specs on their PVA glues Aquadhere etc and they seem to require higher temps than Kleiberi, although they don’t seem to offer as detailed specs as Titebond.

Strength increase in bonded joints over time, 5 min to 7 days It is evident from Fig. At min, its strength equaled that of Propellerleim 3W, 4B, and it subsequently maintained the greatest strength until 7 days after bonding. The tested adhesives achieved this value in a time period of 75 min to min, depending on the adhesive type. Group of loadings – D3 without hardener, D4 – with a hardener.