HDPE Pipes: Specifcations. Specification: IS with latest amendments. Material Grade PE All dimension are in mm. OD PN PN 4. PN 6. PN 8. Dinesh Irrigation Private Limited offering Is HDPE Pipes in Jhotwara, Jaipur , Rajasthan. Get contact details, address, map on Indiamart. | ID: We are leading manufacturer of HDPE pipes as per IS The best quality raw materials are procured to offer the pipes meeting the highest quality.
|Published (Last):||6 November 2014|
|PDF File Size:||18.51 Mb|
|ePub File Size:||6.79 Mb|
|Price:||Free* [*Free Regsitration Required]|
In the absence of a random number table the following procedure may be adopted. Alternatively and for higher sizes, the diameter shall be measured preferably by using a flexible Pi tape or a circometer, having an accuracy of not less than 0. These stripes shall be coextruded during pipe manufacturing and shall not be more than 0.
Is 4984 HDPE Pipes
For coiled pipes, however, re-rounding of pipes shall be carried out piles to the measurement of ovality. Copyright BIS has the copyright of all its publications.
Dhage Alternate Shri M. However, occasional rise in temperature as in summer season with concurrent corresponding reduction in temperature during night has no deleterious effects on the life and working pressure of the pipes. Shembekar Alternate Dr Y. Standards are also reviewed periodically; a standard along with amendments is reaffirmed when such review indicates that no changes are needed; if the review indicates that changes are needed, it is taken up for revision.
Bentex HDPE Pipe As Per Is , Application:Drinking Water, Rs 45 /meter | ID:
All pieces are required to be tested. This Indian Standard has been developed from Doc: In case of variation in water temperature, the working pressure needs to be modified as. Call Send a quick message.
Number of Employees 51 to People. Being the leading names in the industry, we offer our clients an exceptional range of HDPE Plastic Pipes that are durable in nature and hcpe sturdy in construction. The material of pipe thus produced shall conform to requirements of 5.
Sinha Alternate Shri O. The test pieces shall be kept in pipds oven at the temperatures and for the periods specified below: Users of Indian Standards should ascertain that they are in possession of the latest amendments or edition by referring to the latest issue of ‘BIS Handbook’ and ‘Standards Monthly Additions’.
The basis for the values specified is: The glass plate with the test pieces shall then be placed in the oven heated to test temperature and capable of maintaining continuous forced air circulation. No part of these publications may be reproduced in any form without the prior permission in writing of BIS.
HDPE Pipes – Jain High Density Polyethylene Pipes
Find more suppliers in Mumbai Hdpe Tube in Mumbai. The anti-oxidant used shall be physiologically harm- less and shall be selected from the list given in IS Patel Alternate Dr H.
A mark shall be scribed on the external surface approximately 50 mm from each end of the test pieces in the axial direction of pipe, in the case of complete section of pipe, the mark shall be scribed around the whole circumference. Yadav Alternate Shri G. For ascertaining conformity of the lot to the require- ments of this specification, samples shall be selected in accordance with the provisions as men- tioned under 9.
Nominal diameter Maximum out of square DN of pipe end mm mm 16 to 75 2 90 to 3 to 4 to 5 Above 7 Page 9, Annex A, A-l — Substitute the following for the existing clause: A pipe failing to satisfy any of these requirements shall be considered as defective.
The lot shall be considered to have satisfied these require- ments, if the number of defectives found in the cumula- tive sample is less than or equal to the corresponding acceptance number given in col 5 of Table 7; otherwise iiOi. Sharma Alternate Shri O.
View Contact Call Seller Now. Year of Establishment For pipes to be coiled, the ovality shall be measured prior to coiling. Page 11, Annex C, clause C