BD649 DATASHEET PDF

Collector-base voltage (IE = 0). BD BD BD BD The device characteristics and parameters in this data sheet can and do vary. BD Transistor Datasheet pdf, BD Equivalent. Parameters and Characteristics. BD Bourns Darlington Transistors W NPN Silicon datasheet, inventory, & pricing.

Author: Kami Shaktirg
Country: Liberia
Language: English (Spanish)
Genre: Photos
Published (Last): 2 September 2005
Pages: 128
PDF File Size: 7.21 Mb
ePub File Size: 12.56 Mb
ISBN: 360-8-20580-841-1
Downloads: 40558
Price: Free* [*Free Regsitration Required]
Uploader: Arar

No, create an account now.

Jul 22, 9. Jul 22, 8. Quote of the day.

You May Also Like: So, yes I guess the IR filter might help, but the twisted pair is perhaps excessive? Jul 21, 3.

BD – ST/ – Transistors (BJT) – Single – Kynix Semiconductor

OK thank you all for your thoughts on this. B649 looked on-line and saw some diagrams without an R1 or an R2, but wouldn’t that blow the BD or the photo transistor when it saturates? R1 is k and R3 is 50k. Now, putting the opto-transistor right in front of the built-in flash? I think there should be one in series with the opto-transistor, so I can adjust the voltage at the point to the darlington to be 0v at ambient light. Jul 21, 1.

Jul 21, 7 0. Mar 1, 3, 2, The datasheet says the gain is aboutbut daasheet seem to have a different data sheet fatasheet different gain values for different mA and volt values. R1 should only be necessary if the adjustment leg will eat too much current when the flash fires.

  FANSADOX BLACK VAN PDF

The light source consists of five series of ten bright white LEDs, each series with it’s own ohm resistor. May 27, 52 That’s what an SCR and a datasheett will do. Mar 5, 1, How are you with mosfets?

When I shine a torch on the photo resistor, it saturates and the LEDs light up bright, but when I try to activate the system with the flash, the LEDs don’t seem to work.

Will this work if you don’t have any way to stop the LEDs quickly? The Darlington transistor needs about 1.

The opto-transistor can only allow. But I think that’s what you’re saying albeit in other words ;- Dahasheet, if R1 and R2 are high enough, the current through the base of the darlington would also be limited to a safe level.

Jul 22, 6.

BD649 Datasheet

Sep 24, 2, Suppose the PT is 5 mS and the darlington is 20 mS. What you want to do is allow the input power source to charge up a capacitor, and then when your light sensor senses the external flash, dump that cap into the LEDs. And the tailing off from the phosphorous in the white LEDs may become a problem at fast moving objects. OK, I’m going to open my mouth on this.

  GAJO PETROVIC PDF

BD Transistor NPN-Darl TO V 8A W at reichelt elektronik

If the current assumption is that it receives too much light and we have to reduce it with the IR filter. That’s not going to blow out anything. Yes, my password is: I’d thought of this too, to protect the dtaasheet in case I dialled the trim pot meter to 0ohm. Jul 23, See where I’m going with this? And using the hot accessory shoe would be an option, but I like the challenge of wireless, and so far I’m not yet convinced that using the hot shoe would solve the problems I’m encountering here.

Determining resistor values in a mesh. I want it to be triggered by the camera’s built in flash, but I can’t get it to work satisfactorily. Do you already have an account? Datasheft I guess my main question is, how do I calculate the size of R1 and R2 so it protects both the opto-transistor and the base of the darlington at bd694.

I’m a newbie The recommended current through the LEDs is 20mA and the max mA OK for a short flashhence the smaller resistors when the system is in flash mode.